实物链接:点击跳转
开题报告链接:点击跳转
设计说明书:点击跳转
总字数:11000+
摘要
随着人们生活水平的提高,人们个人的财富也越来越多,因此对这些财产的保护就越来越重要,当前人们大多都是通过锁来对其进行保护的。本文设计了一款控制物联网刷卡锁检测,主要分为硬件部分和软件两个部分进行设计:硬件部分、软件部分。硬件部分:主要采用STM32单片机作为主控芯片,采用WiFi作为远程发送刷卡锁的模块,采用RFID用户可以近距离进行刷卡开门;软件部分,采用Keil5作为此次设计程序编程软件,采用AD作为此次设计的原理图和PCB的绘制软件,采用stc-isp作为此次设计程序的烧录软件,采用Visio作为此次设计的流程图绘制软件;通过软件和硬件的配合,使得此次设计的系统可以实现用户可以手机连接热点,从而远程非接触控制电磁锁的开关,也可以通过RFID进行刷卡开锁,此次设计可更好的诠释科技的发展,体现出生活用品的智能化、人性化。
关键词:STM32C8T6;WIFI模块;RFID模块;电磁锁
Abstract
With the improvement of people's living standard, people's personal wealth is also more and more, so the protection of these properties is more and more important. At present, most people protect them through locks. This paper designs a control card swipe lock detection for the Internet of things, which is mainly divided into two parts: hardware part and software part. Hardware: STM32 microcontroller is mainly used as the main control chip, WiFi is used as the module to send the card lock remotely, and RFID users can swipe the card to open the door at close range. In the software part, Keil5 is used as the programming software of the design, AD is used as the drawing software of the schematic diagram and PCB of the design, STC-ISP is used as the burning software of the design program, and Visio is used as the drawing software of the flow chart of the design. Through the cooperation of software and hardware, the design system can realize the user can connect the hot spot of the mobile phone, so as to control the switch of the remote non-contact electromagnetic lock, and can also be swiping through the RFID to unlock the lock. The design can better interpret the development of science and technology, reflecting the intelligence and humanization of daily necessities.
Keywords:STM32C8T6; WIFI module; RFID module; Electromagnetic lock
目录
摘 要
Abstract
第一章 绪论
1.1 选题背景及实际意义
1.2 国内外发展历程
1.3 本论文研究目标与框架
第2章 系统设计方案
2.1 主要元器件选择
2.1.1 主控芯片选择
2.1.2 无线传输方案选择
2.2 整体设计方案
第3章 硬件设计
3.1 主控模块电路
3.1.1 主控模块电路
3.1.2 晶振电路
3.1.3 复位电路
3.1.4 电源电路
3.2 RFID模块电路
3.3 WIFI模块电路
3.4 继电器模块电路
第4章 系统程序设计
4.1 编程软件介绍
4.2 主程序流程设计
4.3 监测函数流程设计
4.4 处理函数流程设计
第5章 实物制作与调试过程
5.1 实物调试部分
5.2 RFID刷卡实物测试
5.3 WiFi远程控制电磁锁实物测试
第6章 结论
参 考 文 献
致谢
附录
附录A: 原理图
附录B:PCB
附录C:主程序